Skip to content
golfclubcharts

Golf club parts

Tap any part on the diagram to see what it does and the spec it sets on an iron, a driver or a putter.

Golf club diagram

Ten parts from grip to sole. Switch between an iron, a driver and a putter.

HEAD CLOSE-UP12345678910
Club

Part 5 of 10 · PING G440 7 iron

Hosel

The neck that joins the head to the shaft. Its angle sets the lie, and on many drivers it holds the adjustable sleeve.

On this club62°Lie angle of the PING G440 7 iron. PING marks lie with a color dot

More: lie angle chart.

Source: PING G440 irons specifications

lie 62°loft 29°

Loft lives on the face, lie on the hosel

The face tilts back by the loft: 29° on the G440 7 iron. The hosel sets the lie, the shaft’s angle to the ground: 62°. Bending the hosel changes both.

7i · 9°PW · 13°SW · 14°

The sole carries the bounce

The sole is the bottom of the head. Its angle from leading edge to low point is the bounce: 9° on the G440 7 iron, 13° on the PW and 14° on the SW.

toe uptoo uprightheel uptoo flat

Toe and heel tell you the lie fits

Sole the club at address. If the toe sits up off the ground, the lie is too upright for you; if the heel sits up, it is too flat. The lie angle chart gives the fix.

Every part and its spec

PartWhat it doesIron (G440 7 iron)Driver (G440)Putter (Scotty Cameron)
1. Butt capThe closed end of the grip at the top of the club.37″46″34″
2. GripThe rubber or cord sleeve your hands hold. Its size changes how easily the hands release the face.by hand sizeby hand sizeby hand size
3. ShaftThe tube between grip and head, in steel or graphite. Its flex, weight and length shape launch and timing.37″46″34″
4. FerruleThe small plastic ring where the shaft goes into the hosel. It hides the joint and smooths the step between shaft and hosel.trim ringtrim ringtrim ring
5. HoselThe neck that joins the head to the shaft. Its angle sets the lie, and on many drivers it holds the adjustable sleeve.62°58½°70°
6. ClubheadEverything below the hosel: the part that meets the ball. Wood, hybrid, iron, wedge and putter heads each have their own shape.29° / 62°10½° / 58½°3½° / 70°
7. FaceThe hitting surface. Its tilt back from vertical is the loft; irons and wedges cut grooves across it for spin.29°10½°3½°
8. ToeThe end of the head farthest from the shaft. A toe sitting up at address means the lie is too upright for you.toe up / downtoe up / downtoe up / down
9. HeelThe end of the head nearest the shaft. Shots struck here fly low and often start right for a right-hander.heel sideheel sideheel side
10. SoleThe bottom of the head that rests on the ground. The angle between its leading edge and its lowest point is the bounce.9° bounceflat, wideflat

Source: PING G440 irons specifications; PING G440 K driver specifications; Scotty Cameron Studio Style putter specifications; USGA and R&A Model Local Rule G-10 (club length)

The main sections, grip to head

Grip

The butt cap and the rubber or cord sleeve. Sized by hand: the grip size chart maps hand length to standard, midsize and jumbo.

Shaft

Steel or graphite, from the grip to the ferrule. Its length sets club length (37″ on the 7 iron, 46″ on the driver); its flex and weight set launch.

The joint

The ferrule and hosel, where shaft meets head. The ferrule is a trim ring with no spec; the hosel angle is the lie (62° on this 7 iron), and PING marks it with a color dot.

Head

Face, toe, heel and sole. The face sets loft and the sole sets bounce. Head shape is what makes a club a wood, hybrid, iron, wedge or putter.

Worked example: reading a 7 iron

  1. Butt to sole: the G440 7 iron is 37″ long, measured to the end of the grip.
  2. Face: 29° of loft. The 8 iron next to it is 33°.
  3. Hosel: 62° lie. PING marks the lie with a color dot on the hosel; see the PING color code chart.
  4. Sole: 9° of bounce, less than the wedges, so it does not skip off firm turf.
  5. At address the toe sits up? Then that 62° is too upright for you. A fitter bends the hosel flatter.

Driver parts that differ

The driver is built differently

The G440 driver head comes in 9°, 10½°, 12° and sits on an adjustable sleeve in the hosel, so loft and lie change together. Its 46″ length is under the Rules’ 48″ cap, and exactly the 46″ a competition can set under Local Rule G-10 (since 1 January 2022).

Source: PING G440 K driver specifications; USGA and R&A Model Local Rule G-10 (club length)

The putter is the other exception: its 70° lie is the most upright in the bag, and its sole should sit flat when you take your putting posture. Length runs 33, 34, 35″ in Scotty Cameron’s stock range; fit it on the putter length page.

Questions golfers ask

What are the parts of a golf club called?

From top to bottom: butt cap, grip, shaft, ferrule, hosel and head. The head has a face, toe, heel and sole.

What is the hosel on a golf club?

The neck that joins the head to the shaft. Its angle sets the lie (62° on the PING G440 7 iron), and on most drivers it holds the adjustable sleeve.

What is the ferrule on a golf club?

The small plastic ring where the shaft enters the hosel. It is cosmetic and is replaced when the club is re-shafted.

What is the toe and heel of a golf club?

The toe is the end of the head farthest from the shaft, the heel the end nearest it. Which one sits up at address tells you whether the lie fits.

Where is the sole on a golf club?

The bottom of the head, the part that rests on the ground. Its shape sets the bounce: 9° on a G440 7 iron, 14° on its sand wedge.